Vibration and Geometrical Analysis of Briquette Mixing and Molding Machine
DOI:
https://doi.org/10.56862/irajtma.v5i2.386Keywords:
Briquette machine, Geometrical analysis, Vibration analysis, Sustainable energyAbstract
This study analyses the vibration characteristics of a mixing and briquette molding machine and the effect of frame geometry conditions on its dynamic response based on experimental measurements. This research aims to evaluate the vibration level caused by structural geometric misalignment. The methods used include vibration measurements using a vibration tester at critical points of the machine frame and flatness measurements using a spirit level. Vibration amplitude is determined from the maximum displacement at each point and measurement direction. The results show that the highest amplitude occurs at point 4 in the vertical direction, reaching 0.1027 mm, while the lowest amplitude is found at point 2 in the axial direction, measuring 0.0427 mm. The dominance of vertical vibration indicates the influence of gravitational forces and frame misalignment. Vibration amplitude varies with the position of measurement points relative to dynamic load sources and structural stiffness. No resonance is observed, indicating that the vibrations are forced vibrations caused by system imbalance. Flatness deviations of 0.0073 mm (horizontal) and 0.152 mm (axial) contribute to increased vibration amplitude, confirming that frame geometry significantly affects vibration levels.
References
Anggono, W. ., Hernando, I. C., & Yuke, S. . (2026). Combustion Characteristics of Coconut Coir Waste Briquettes Using Pineapple Waste Binder under Different Compaction Pressures. IRA Jurnal Teknik Mesin Dan Aplikasinya (IRAJTMA), 5(1), 128–136. https://doi.org/10.56862/irajtma.v5i1.419
BPH Migas. 2024. Laporan Kinerja / “Laporan Tahunan BPH Migas 2024”. Jakarta: Kementrian ESDM.
Bahri Widodo, S., Arif, Z., Yakob, I., Suheri, S., & Sembiring, D. M. (2025). Study of Utilization of Water Hyacinth (Eichhornia Crassipes) as Environmentally Friendly Bio-Briquettes: Experimental Study. IRA Jurnal Teknik Mesin Dan Aplikasinya (IRAJTMA), 4(1), 48–58. https://doi.org/10.56862/irajtma.v4i1.193
Cheng, Xiaohan, Aiming Wang, and Guangqiang Wu. 2022. "Vibration analysis of a deep groove ball bearing with localized and distributed faults subject to waviness based on an improved model under time-varying speed condition." Sage Journals 3259–3274. https://doi.org/10.1177/10775463221094162
Eswanto, Hamidi, M. A., Daud, S., Yusop, A. F., & Allehaibi, M. (2026). Hydrogen Fuel Addition in Diesel Engines: Current and Future Research Trends through Bibliometric Analysis. Journal of Computers, Mechanical and Management, 5(3), 311–333. https://doi.org/10.57159/jcmm.5.3.26566
Eswanto, Hamidi M.A., Daud S, Yusop A.F., Kifli U., Iwan G. (2025). Hydrogen-induced Fuel System in RCCI Engine for Clean Combustion: A Review, AutomotiveExperiences, 8 (2), 310-337. https://doi.org/10.31603/ae.13722
Hanafie, Dirga Wirayudha A., Mei Hardiana , and Nurul Fadhilah. 2023 . Rancang Bangun Mesin Pengaduk Pada Proses Pembuatan Briket Arang Tempurung Kelapa. Makassar : Politeknik Negeri Ujung Pandang.
Kementrian ESDM. 2023. Statistik Energi Indonesia 2023 / Handbook of Energy & Economic Statistics Indonesia (HEESI 2023). jakarta: Kementrian ESDM.
Sanam, Muhdori, and Hamid Abdillah. 2023. Analisis Standar Getaran Mesin Gerinda Duduk Berdasarkan ISO 2372 Akibat Variasi Material Benda Kerja. Jurnal Teknik Mesin. 12(3), 206-211.
Siagian, Tony. (2022). "Analisa Getaran Dan Koefisien Korelasi Antara Getaran Pada Mesin (Engine) Dan Tempat Duduk Operator (Seat) Dengan Variasi Tingkat Kebisingan Mesin Forklift Type Fd 30 Pa Sumitomo ." Jurnal Al Ulum LPPM Universitas Al Washliyah Medan. 10(2), 54-60. https://ejurnal.univamedan.ac.id/index.php/alulum/article/view/233/310
Siagian, T. ., Siregar, I. ., Hasibuan, E. ., Saktisahdan, T. J. ., Zahar, I. ., & Purnama, B. (2025). The Effect of Variations in Raw Materials (Coconut Shells, Rice Husks, Rubber Wood Sawdust) and Adhesive Composition on the Physical Properties of Biomass Briquettes. IRA Jurnal Teknik Mesin Dan Aplikasinya (IRAJTMA), 4(3), 246–253. https://doi.org/10.56862/irajtma.v4i3.358
Soolany, Christian. (2020). "Rancang Bangun Pencetak Briket Tipe Screw Untuk Proses Produksi Briket Pelet Dari Arang Cangkang Kakao." AME(Aplikasi Mekanika dan Energi) 63. https://doi.org/10.32832/ame.v6i2.3260
Syahbilla, Muthiara, Husman, and Erwansyah. (2024). "Uji Metrologi Gerak Melingkar Pada Mesin CNC Milling Di Bengkel Mekanik Polmanbabel." JITT (Jurnal Inovasi Teknologi Terapan). 2(2), 365-370. https://doi.org/10.33504/jitt.v2i2.175
Triswandi, Riky, Fadly A. Kurniawan, Din Aswan A. Ritonga, and Junaidi. (2023). "Analisa Getaran Menggunakan Bantalan Mesin (Engine Mounting) Berbahan Dasar Kombinasi Dua Per Spiral Dan Karet Alami Pada Toyota Avanza." Buletin Utama Teknik. 18(23), 237-244. https://doi.org/10.30743/but.v18i3.7632
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Jupri Yanda Zaira Zaira, Mustaza Ma’a, Agus Wijianto, Rio Hardyanto
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
