Design and Manufacture of Free Fall Impact Test Equipment with Drop Weight Test model.

Authors

  • Mahyunis Institut Teknologi Sawit Indonesia
  • Nurdiana Universitas Al-Azhar Medan
  • Sari Farah Dina Politeknik Teknologi Kimia Industri
  • Ahmad Wito Pirmansyah Institut Teknologi Medan

DOI:

https://doi.org/10.56862/irajtma.v1i1.8

Keywords:

Free Fall Impact Test Equipment Design, Drop Weight Test Method, Manufacturing

Abstract

The rapid development of technology today is a challenge that must be considered by making technology itself. However, not many pay attention to the qualified aspects that must be in technology.  Which can have a bad influence on the work environment. Therefore, this study aims to obtain a re-design and model of a free fall impact test equipment, obtain the main components of a free fall impact test equipment with the drop weight test method and obtain a manufacturing process. This design method uses Autocad software and Ansys Workbench Simulation 14.5. Based on the simulation results, the free fall impact test equipment with the number of each component, namely: 3-node and 4-node. The difference between theoretical calculations and simulation calculations in each component, namely the main structure pole, obtained voltage 1,455, voltage 1.345 and Poisson ratio 0.7, the launcher pipe obtained voltage 1.451, voltage 1.346, Poisson ratio 0.04 and friction coefficient 265.10, anvil table obtained voltage 1.248, Poisson ratio 0.02 and Safety factor 11. The work on the free fall impact test equipment has a manufacturing time of 54.1 minutes.

References

Bodats. 2009. “Dokumentasi Pengujian Helm SNI 1811-2007.” 2009. https://bodats.wordpress.com/2009/10/22/dokumentasi-pengujian-helm-sni-1811-2007/.

Budianto, Kokok Tri, Anggun Rizka Maudina, and Askar Triwiyanto. 2017. “Rancang Bangun Alat Uji Drop Weight Impact Skala Laboratorium” 2 (1): 1–10.

Khurmi, R S. 2015. A Textbook of Engineering Mechanics. New Delhi: S. Chand & Company Ltd.

Pasapan, Yerik. 2011. “Teori Dasar Impact.” PahatBaja28 Blog. 2011. http://pahatbaja.blogspot.com/2011/06/teori-dasar-impact.html.

Ramanta, Ponti. 2007. Helm Pengendara Kendaraan Bermotor Roda Dua. https://www.scribd.com/doc/55109417/SNI-1811-2007.

Ramdaniawati, Deliana. 2014. “Laporan Praktikum Praktikum Pengujian Material Modul 3 -Pengujian Impak.” https://123dok.com/document/z1rwdpeq-laporan-impak.html.

Sahal Digital Media. 2021. “Penjelasan Uji Penyerapan Kejut Dan Uji Penetrasi Pada Sungkup Helm Ber Standar SNI.” 2021. https://www.sahal.my.id/2021/03/penjelasan-uji-penyerapan-kejut-dan-uji.html.

Simanjuntak, Rahmat Kartolo. 2012. “Energi Impak Helmet Sepeda Motor Yang Dikenai Beban Jatuh Bebas.” REINTEK: Jurnal Ilmu Pengetahuan Dan Teknologi Terapan 7 (1): 1–7. https://123dok.com/document/q0xgw0gq-energi-impak-helmet-sepeda-motor-dikenai-beban-jatuh.html.

———. 2017. “Analisa Kekuatan Impak Helmet Sepeda Motor Metode Impak Jatuh Bebas.” Jurnal Inotera 2 (1): 42. https://doi.org/10.31572/inotera.vol2.iss1.2017.id19.

Sreemoballer’s, Hendra. 2013. “Laporan Pengujian Bahan.” https://www.slideshare.net/HendraSreemoballers/laporan-pengujian-bahan-20132014.

Published

2022-08-15 — Updated on 2022-08-15

How to Cite

Mahyunis, Nurdiana, Farah Dina, S., & Wito Pirmansyah, A. . (2022). Design and Manufacture of Free Fall Impact Test Equipment with Drop Weight Test model. IRA Jurnal Teknik Mesin Dan Aplikasinya (IRAJTMA), 1(1), 41–50. https://doi.org/10.56862/irajtma.v1i1.8

Issue

Section

Scientific Article